43 chemicals for thinner
Toluene
CAS 108-88-3Acetone
CAS 67-64-1Butyl Acetate
CAS 123-86-4Benzyl Alcohol
CAS 100-51-6Butanol (NBA)
CAS 71-36-3Butyl Carbitol
CAS 112-34-5Butyl Cellosolve (Glycol)
CAS 111-76-2Butyl Cellosolve Acetate
CAS 112-07-2Di Ethanol Amine (DEA)
CAS 111-42-2Di Methyl Amine (DMA)
CAS 124-40-3Diacetone Alcohol
CAS 123-42-2Ethyl Acetate
CAS 141-78-6Ethyl Cellosolve
CAS 110-80-5Ethyl Cellosolve Acetate
CAS 111-15-9Glycerine
CAS 56-81-5Glycerin USP
CAS 56-81-5Glycerol Mono Stearate (GMS)
CAS 31566-31-1Hexane (Food Grade)
CAS 110-54-3Iso-Butanol
CAS 78-83-1Isopropyl Alcohol (IPA)
CAS 67-63-0Maleic Anhydride
CAS 108-31-6Phthalic Anhydride
CAS 85-44-9Mono Ethanol Amine (MEA)
CAS 141-43-5N-Propanol
CAS 71-23-8N-Propyl Acetate
CAS 109-60-4Tri Ethanol Amine (TEA) 85%/99%
CAS 102-71-62-Ethylhexyl Acrylate
CAS 103-11-72-Ethylhexyl Acetate
CAS 103-09-3Benzene
CAS 71-43-2Butyl Acrylate Monomer (BAM)
CAS 141-32-2Cyclo Hexane
CAS 110-82-7Cyclo Hexanone
CAS 108-94-1Di Methyl Formamide (DMF)
CAS 68-12-2Methyl Ethyl Ketone (MEK)
CAS 78-93-3Methyl Iso Butyl Ketone (MIBK)
CAS 108-10-1Mixed Xylene
CAS 1330-20-7Meta Xylene
CAS 108-38-3Nitro Benzene
CAS 98-95-3Octanol (2EH)
CAS 104-76-7Ortho Xylene
CAS 95-47-6Phenol (Liquid / Crystal)
CAS 108-95-2Styrene Monomer
CAS 100-42-5Vinyl Acetate Monomer (VAM)
CAS 108-05-4Frequently Asked Questions
Do you supply finished thinner, or only the solvents to blend it?
Both. We supply a finished thinner in General Purpose / NC and Commercial grades, sourced from Chennai Petroleum Corporation Limited (CPCL), in 200 L drums and tins as UN 1263. The full specification — specific gravity, distillation range and flash point — is on the Thinners product page. We also supply the individual blending solvents in bulk if you blend in-house.
Which solvents go into a thinner blend?
Thinner is a blend, not a single chemical, so the slate is best read by boiling point. Lowest first: acetone 56.05°C; MEK 79.6°C; IPA 82.5°C; toluene 110.6°C; mixed xylene 137–144°C; MTO 145–210°C. Purities run 99.5% min (GC) for acetone, MEK and toluene, 99.8% min (GC) for IPA, and ≥ 98.5% xylene isomers + ethylbenzene for mixed xylene. The ester and glycol-ether solvents sit alongside them: ethyl acetate 99.80% w/w min, butyl acetate 99.5 % w/w min n-Butyl Acetate, butyl cellosolve 99.0% wt min and butyl carbitol 99.0 % wt min Butyl Diglycol Ether. Grades, packaging and active matter for each are tabulated on our paints and coatings page.
Can you supply thinner solvents in bulk tanker?
Several, but the exceptions are what catch people out. Ethyl acetate is bulk tanker only — dedicated cleaned tankers, roughly 20 MT loads — so there is no drum option. MEK and MTO run the other way: 200L MS barrel and 1000L IBC tank, with no tanker. MIBK is 160 kg HDPE/MS drums only, and the finished CPCL thinner ships in 200 L drums and tins. Our bulk solvent table lists grades and packaging side by side for the rest. Tell us the product and quantity and we will confirm what moves in tanker against what moves in drums.
Do you make thinner?
No. SPC is a trader, importer and bulk distributor. We supply the chemicals for thinner manufacturers, and we also supply a finished General Purpose / NC and Commercial thinner sourced from Chennai Petroleum Corporation Limited (CPCL). We do not formulate or manufacture thinner ourselves.
What is the difference between a thinner and a single solvent?
A thinner is a blend of several solvents, balanced so it evaporates at a controlled rate and dissolves the resin system it is used with. A single solvent such as toluene or acetone is one ingredient. Manufacturers buy the individual solvents and blend them to their own specification; SPC supplies the solvents.
Which solvents evaporate first in a thinner blend?
Lowest boiling point goes first. On the boiling points we publish: acetone 56.05°C, MEK 79.6°C, IPA 82.5°C, toluene 110.6°C, mixed xylene 137–144°C, and MTO 145–210°C. A blend usually mixes fast, mid and slow cuts so the film does not dry too quickly or stay wet too long.
What purity do your thinner solvents run?
Acetone, MEK and toluene are 99.5% min by GC; IPA technical grade is 99.8% min by GC; mixed xylene is at least 98.5% xylene isomers plus ethylbenzene; ethyl acetate is 99.80% w/w min; butyl acetate is 99.5% w/w min n-butyl acetate. A batch Certificate of Analysis is supplied with every delivery.
What are the specifications of the finished CPCL thinner?
The TDS lists: clear, free from suspended matter; colour 20 max (Pt-Co); specific gravity 0.80–0.88 at 30°C; distillation range 60–145°C; flash point 23°C max (Abel); non-volatile matter 0.05% mass max; water content nil; complete evaporation with no residue. It ships in 200 L drums and tins as UN 1263, Class 3.
Is the finished thinner a single published standard?
No. The TDS describes it as a typical commercial grade, a general-purpose / NC thinner blend with no single published numeric standard. Ask for the batch Certificate of Analysis for the values on the lot you receive.
Which packs are available for thinner solvents?
It depends on the product. Toluene, mixed xylene and acetone come in 200 L MS barrels, 1000 L IBC tanks and bulk tanker (acetone also in 160 kg MS drums). MEK and MTO are 200 L barrel and 1000 L IBC with no tanker. Ethyl acetate is bulk tanker only. Butyl acetate is bulk road tanker, HDPE drums or MS drums. Tell us the product and quantity and we confirm the pack.
What should I check when buying solvents for a thinner blend?
Check: the grade and the assay method (GC); the boiling point or distillation range against your target evaporation curve; flash point and UN class for storage and transport; the pack type your site can receive (drum, IBC or tanker); and whether a batch Certificate of Analysis comes with each delivery. Ours does. Also confirm the end use with your own customer or regulator, as suitability for the final application is your decision.
Is the thinner and are the blending solvents flammable?
Yes. Thinners and the solvents that go into them are flammable liquids. The finished thinner is UN 1263, Class 3, flash point 23°C max (Abel), and its safety data sheet carries the signal word Danger with H225 (highly flammable liquid and vapour). Store away from heat, sparks and open flames, with adequate ventilation. Request the SDS for each product before use.
What is in the finished thinner according to the safety data sheet?
The SDS identifies it as a thinner whose principal component is toluene (CAS 108-88-3). It is for industrial and professional use only; confirm suitability for your application before use. Read Section 2 of the SDS for the full hazard classification.
Can I get an NC thinner and the solvents for it from one supplier?
Yes. We supply the finished CPCL thinner in General Purpose / NC and Commercial grades, and the individual solvents (toluene, xylene, MTO, acetone, MEK, IPA, butyl acetate) if you blend in-house. One Certificate of Analysis per batch for each.
How fast can I get a quote?
We quote within 4 working hours. Send the product, grade, pack type and quantity by WhatsApp or the enquiry form.
Do you supply technical-grade solvents for food or pharma use?
No. The solvents on this page are industrial and technical grades for thinner production. IPA is also listed in an Indian Pharmacopoeia grade on its own product page, but technical grade is not food or pharma grade, and we do not offer it as such.
Deep guidesThinners — CPCL General Purpose / NC gradesPaint and coating raw materials — grades and packagingBulk solvent table — grades and packagingToluene vs mixed xylene — selection guideMEK vs MIBK vs acetone — ketone selectionIsopropyl alcohol (IPA) — Technical and IP gradesToluene — Industrial, Technical and Nitration gradesButyl acetate — solvent gradeMineral turpentine oil (MTO)
Sourcing chemicals for thinner?
Tell us your requirement — product, quantity, and frequency. We respond within 4 working hours with pricing and availability.