AcidsChemical PowderOther Chemicals

Water Treatment Chemical Supplier — Chennai

Supreme Petro Chemicals supplies chemicals for water treatment manufacturers and plant operators, organised by treatment stage: chlorine sources and hydrogen peroxide, caustic soda, soda ash and mineral acids for pH, scale and hardness control, and sulphite reducing agents. We are an importer and bulk distributor, not a producer of finished treatment products. Quote within 4 working hours; a batch Certificate of Analysis is supplied with every delivery.

Chemicals by treatment stage

Chemicals for each stage of the treatment train.

01

Disinfection, oxidation & algae control

Chlorine sources and oxidisers. Bleaching powder is calcium hypochlorite to IS 1065 (Part 1) carrying 30-35% available chlorine by mass. Imported TCCA 90 is granular, 5-8 mesh, with 90% minimum available chlorine. Hydrogen peroxide is the clean oxidiser, in 35% and 50% w/w technical grades. Copper sulphate is the water-soluble copper source listed for water treatment and algaecide duty. General process note, not an SPC specification: disinfection normally follows clarification, because suspended solids use up chlorine; the dose is set from your measured demand and residual, not from a supplier figure. All of these are oxidisers (Class 5.1): keep them apart from acids, reducing agents and combustibles.

ProductGrade we supplyActive matter / key specCASPackaging
Bleaching PowderStable, IS 1065 (Part 1)Available chlorine 30–35% by mass7778-54-350 kg HDPE drums
Trichloroisocyanuric Acid (TCCA)Granular, 5-8 Mesh (90% available chlorine)Available chlorine 90% min87-90-125 kg HDPE drum, 50 kg HDPE drum
Hydrogen PeroxideTechnical (35%) / Technical (50%) / Electronic grade / Pharma grade35% w/w (commercial); 50% w/w (technical)7722-84-135 kg HDPE carboy, 70 kg HDPE barrel, 200 kg HDPE barrel, 1000L HDPE IBC
Copper SulphateTechnical / Agricultural / Industrial≥ 98% CuSO₄·5H₂O7758-99-825 kg HDPE bag, 50 kg woven sack
02

pH correction, acids & alkalis

pH correction runs in both directions. Caustic soda flakes, 47% caustic soda lye and soda ash light raise pH and alkalinity; hydrochloric, sulphuric and phosphoric acid bring it down. General process note, not an SPC specification: neutralisation is usually staged with a pH probe and the choice between acids is driven by what the downstream process tolerates (for example, sulphate or chloride load). Packaging spans 25 kg bags and 35 kg carboys up to bulk road tanker, with a rubber-lined tanker for hydrochloric acid.

ProductGrade we supplyActive matter / key specCASPackaging
Caustic SodaIndustrial flakes / Pearls / prills / Rayon grade98% min NaOH1310-73-225 kg HDPE bag, 50 kg HDPE bag, 1000 kg jumbo bag
Caustic Soda LyeIS 252:2013 Grade-1 (BIS CM/L-6100076189)47% min NaOH (as NaOH, by mass)1310-73-2Bulk road tanker
Soda AshSoda Ash Light, 99.0% min99.00% min (total alkalinity as Na2CO3)497-19-850 kg HDPE bags
Hydrochloric Acid (HCL)Commercial (30%) / Technical (33%) / Synthetic (35%)30% min (commercial grade)7647-01-035 kg HDPE carboy, 200L HDPE barrel, 1000L HDPE IBC, Bulk rubber-lined tanker
Sulphuric AcidCommercial 98%98.0% min by mass (acid concentration)7664-93-9Carboys, Bulk road tanker
Phosphoric AcidOrthophosphoric Acid, Technical Grade86.0% min Orthophosphoric Acid (H3PO4); 62.3% min P2O57664-38-250 kg carboy
03

Scale, hardness & sequestration

Hardness ions foul heat-transfer surfaces and membranes, so they are bound before they can deposit. SHMP is listed as a scale and corrosion inhibitor for industrial water treatment, STPP as a scale-control agent for ETP and cooling-water systems, and EDTA as the chelating agent that sequesters metal ions across the range. Sodium gluconate is listed for scale and corrosion inhibition in water treatment. General process note, not an SPC specification: threshold phosphates such as SHMP hold scale-forming salts in solution at low dose, whereas chelants such as EDTA and gluconate bind the metal ions themselves; which suits a system depends on temperature, pH and water chemistry. SHMP and STPP differ in the pH of a 1% solution (5.8-6.8 against 9.2-10.0).

ProductGrade we supplyActive matter / key specCASPackaging
SHMP (Sodium Hexametaphosphate)Technical Grade (P2O5 68% min)Total phosphate (as P2O5) 68.0% mass min10124-56-850 kg HDPE/laminated bags
STPP (Sodium Tripolyphosphate)Technical Grade94.0 % mass min (as Na5P3O10); total phosphate (as P2O5) 57.0 % mass min7758-29-450 kg HDPE/laminated bags
EDTA — All TypesDi-Sodium (technical grade)99.0–101.0% (EDTA-2Na, dried basis)60-00-425 kg bags
Sodium GluconateTechnical98.0 – 102.0%527-07-125 kg bags
04

Dechlorination & oxygen scavenging

Residual chlorine damages an RO membrane, so it is reduced out upstream. SMBS and sodium bisulphite are listed as reducing agents and oxygen scavengers for water and effluent treatment; sodium sulphite is the third sulphite, supplied as anhydrous technical grade. General process note, not an SPC specification: the sulphite dose is set from the measured residual chlorine or dissolved oxygen, and the same group of chemicals is used to scavenge oxygen in boiler water. Keep sulphites away from acids: they release sulphur dioxide.

ProductGrade we supplyActive matter / key specCASPackaging
Sodium Meta Bi Sulphite (SMBS)Industrial Grade (Superior)96.0% mass min (Na2S2O5)7681-57-425 kg bag, 50 kg bag
Sodium Bi SulphiteTechnical GradeAvailable SO2, 35.0% min (mass)7631-90-550 kg HDPE bags (powder), HDPE carboys (solution)
Sodium SulphiteTechnical (anhydrous)>= 97% Na2SO37757-83-725 kg HDPE bag, 50 kg woven sack

Figures are the grades and specifications we supply, as published on each product page. A batch Certificate of Analysis carries the exact numbers.

Relevant Products

85 chemicals for water treatment

Request Bulk Quote
Chemical PowderFeatured

Sodium Gluconate

CAS 527-07-1
View details
Acids

Acetic Acid

CAS 64-19-7
View details
Acids

Acid Slurry

CAS 27176-87-0
View details
Acids

Acid Thickener

View details
Acids

Acrylic Acid

CAS 79-10-7
View details
Acids

Alphox 200

CAS 9016-45-9
View details
Acids

Benzoic Acid

CAS 65-85-0
View details
Acids

Boric Acid

CAS 10043-35-3
View details
Acids

Chromic Acid

CAS 1333-82-0
View details
Acids

Citric Acid Anhydrous

CAS 77-92-9
View details
Acids

Citric Acid Monohydrate

CAS 5949-29-1
View details
Acids

Formic Acid

CAS 64-18-6
View details
Acids

Fumaric Acid

CAS 110-17-8
View details
Acids

Hydrochloric Acid (HCL)

CAS 7647-01-0
View details
Acids

Hydrogen Peroxide

CAS 7722-84-1
View details
Acids

Nitric Acid

CAS 7697-37-2
View details
Acids

Oleic Acid

CAS 112-80-1
View details
Acids

Oxalic Acid

CAS 6153-56-6
View details
Acids

Phosphoric Acid

CAS 7664-38-2
View details
Acids

Sulphuric Acid

CAS 7664-93-9
View details
Chemical Powder

AOS (Paste / Liquid / Powder)

CAS 68439-57-6
View details
Chemical Powder

Benzoyl Peroxide Powder (BPP)

CAS 94-36-0
View details
Chemical Powder

Bleaching Powder

CAS 7778-54-3
View details
Chemical Powder

Borax

CAS 1303-96-4
View details
Chemical Powder

Camphor

CAS 76-22-2
View details
Chemical Powder

Caustic Potash

CAS 1310-58-3
View details
Chemical Powder

Caustic Soda

CAS 1310-73-2
View details
Chemical Powder

Ceto Stearyl Alcohol

CAS 67762-27-0
View details
Chemical Powder

Cetyl Alcohol

CAS 36653-82-4
View details
Chemical Powder

CM-1000

View details
Chemical Powder

EDTA — All Types

CAS 60-00-4
View details
Chemical Powder

Magnesium Nitrate

CAS 13446-18-9
View details
Chemical Powder

Maize Starch

CAS 9005-25-8
View details
Chemical Powder

Melamine

CAS 108-78-1
View details
Chemical Powder

Paraformaldehyde

CAS 30525-89-4
View details
Chemical Powder

SHMP

CAS 10124-56-8
View details
Chemical Powder

SLS Powder

CAS 151-21-3
View details
Chemical Powder

Soda Ash

CAS 497-19-8
View details
Chemical Powder

Sodium Acetate

CAS 6131-90-4
View details
Chemical Powder

Sodium Benzoate

CAS 532-32-1
View details
Chemical Powder

Sodium Bi Sulphate

CAS 7681-38-1
View details
Chemical Powder

Sodium Bi Sulphite

CAS 7631-90-5
View details
Chemical Powder

Sodium Bicarbonate

CAS 144-55-8
View details
Chemical Powder

Sodium Bromate

CAS 7789-38-0
View details
Chemical Powder

Sodium Di Chromate

CAS 10588-01-9
View details
Chemical Powder

Sodium Ligno Sulphonate

CAS 8061-51-6
View details
Chemical Powder

Sodium Meta Bi Sulphite (SMBS)

CAS 7681-57-4
View details
Chemical Powder

Sodium Nitrate

CAS 7631-99-4
View details
Chemical Powder

Sodium Nitrite

CAS 7632-00-0
View details
Chemical Powder

Sodium Silicate

CAS 1344-09-8
View details
Chemical Powder

Sodium Sulphate

CAS 7757-82-6
View details
Chemical Powder

Stearic Acid

CAS 57-11-4
View details
Chemical Powder

STPP

CAS 7758-29-4
View details
Chemical Powder

Titanium Dioxide (Anatase / Rutile)

CAS 13463-67-7
View details
Chemical Powder

Trichloroisocyanuric Acid (TCCA)

CAS 87-90-1
View details
Chemical Powder

Xanthan Gum

CAS 11138-66-2
View details
Other Chemicals

Acetonitrile

CAS 75-05-8
View details
Other Chemicals

Alkyd Resin

CAS 63148-69-6
View details
Other Chemicals

Caustic Soda Lye

CAS 1310-73-2
View details
Other Chemicals

Chloroform

CAS 67-66-3
View details
Other Chemicals

Cocamidopropyl Betaine (CAPB)

CAS 61789-40-0
View details
Other Chemicals

Coco Di — CDEA

CAS 68603-42-9
View details
Other Chemicals

Coco Mono — CMEA

CAS 68140-00-1
View details
Other Chemicals

Common Salt (Sodium Chloride)

CAS 7647-14-5
View details
Other Chemicals

Copper Sulphate

CAS 7758-99-8
View details
Other Chemicals

Di Pentene

CAS 138-86-3
View details
Other Chemicals

Formaldehyde

CAS 50-00-0
View details
Other Chemicals

Light / Heavy Liquid Paraffin (LLP / HLP)

CAS 8012-95-1
View details
Other Chemicals

Linear Alkyl Benzene (LAB)

CAS 67774-74-7
View details
Other Chemicals

Liquor Ammonia

CAS 1336-21-6
View details
Other Chemicals

Mineral Turpentine Oil (MTO)

CAS 8052-41-3
View details
Other Chemicals

Mono Sodium Glutamate (MSG)

CAS 6106-04-3
View details
Other Chemicals

Morpholine

CAS 110-91-8
View details
Other Chemicals

Paraffin Wax (Hard / Light)

CAS 8002-74-2
View details
Other Chemicals

Pine Oil (22% / 32% / 42%)

CAS 8002-09-3
View details
Other Chemicals

Silicone Emulsion / Oil

CAS 63148-62-9
View details
Other Chemicals

SLES Liquid / Paste

CAS 68585-34-2
View details
Other Chemicals

Sorbitol

CAS 50-70-4
View details
Other Chemicals

Thinners

View details
Other Chemicals

Tween 20 (Polysorbate 20)

CAS 9005-64-5
View details
Other Chemicals

Tween 80 (Polysorbate 80)

CAS 9005-65-6
View details
Other Chemicals

Urea

CAS 57-13-6
View details
Other Chemicals

White Petroleum Jelly

CAS 8009-03-8
View details
Other Chemicals

Sodium Sulphite

CAS 7757-83-7
View details
Other Chemicals

Zinc Oxide

CAS 1314-13-2
View details
Why SPC

Why SPC for Water Treatment

01

Chemicals for each treatment stage from one supplier: bleaching powder and TCCA for chlorination, caustic soda, soda ash and mineral acids for pH, SHMP, STPP and EDTA against scale, SMBS for dechlorination

02

Pack formats that follow the chemical: bags and drums for solids, carboys and IBCs for liquids, and bulk road tanker for caustic soda lye, sulphuric acid and hydrochloric acid (rubber-lined tanker)

03

A batch Certificate of Analysis is supplied with every delivery, with TDS and SDS on request, so audit files stay complete

Before you enquire

  • Name the stage and the water: raw water, effluent, cooling, boiler or RO feed. The same chemical is bought for different duties and the right grade follows the duty.
  • Say whether the use touches drinking water. Our grades are technical or industrial unless the product page says otherwise; potable-water approval requirements are set by your regulator and operator, so tell us the requirement and we will confirm what the grade documents show. We do not describe a technical grade as food or pharma grade.
  • Work from active content, not product name: available chlorine (bleaching powder 30-35%, TCCA 90% min), NaOH (flakes 97.0% min as supplied, 99.5% dry basis per IS 252:2013; lye 47% min), total alkalinity (soda ash 99.00% min), P2O5 (SHMP 68.0% min), SO2 or Na2S2O5 (bisulphite, SMBS). Dose is your plant number, not ours.
  • Match the pack to your unloading: bags and drums for solids, carboys, barrels and IBCs for liquids, bulk road tanker for caustic soda lye, sulphuric acid and hydrochloric acid (rubber-lined tanker).
  • Plan storage before the material arrives: oxidisers (bleaching powder, TCCA, hydrogen peroxide) apart from acids, reducing agents and combustibles; sulphites apart from acids; do not seal hydrogen peroxide containers.
  • Never mix chlorine sources with acids or ammonia: TCCA and bleaching powder release chlorine, and bisulphite and SMBS release sulphur dioxide with acids.
  • Ask for the batch Certificate of Analysis, TDS and SDS with the quote, and file them against the lot.
  • Send the requirement for a quote within 4 working hours.

Frequently Asked Questions

Which chemicals do you supply for an effluent treatment plant?

We supply the sequence by stage, not a single item. Disinfection and oxidation: bleaching powder, TCCA and hydrogen peroxide. pH correction: caustic soda, caustic soda lye, soda ash, and hydrochloric, sulphuric and phosphoric acid. Scale and hardness: SHMP, STPP, EDTA and sodium gluconate. Dechlorination and oxygen scavenging: SMBS, sodium bisulphite and sodium sulphite. Send the stage and volume for a quote within 4 working hours.

Which chemical removes residual chlorine before an RO membrane?

A sulphite reducing agent. We supply Sodium Meta Bi Sulphite (SMBS), Industrial Grade (Superior), at 96.0% mass min Na2S2O5 in 25 kg and 50 kg bags, and sodium bisulphite, Technical Grade, at available SO2 35.0% min (mass), as powder in 50 kg HDPE bags or as solution in HDPE carboys. We do not publish dose rates: the right dose follows your measured residual chlorine, which is plant-specific.

What is TCCA 90 and what does the grade mean?

TCCA is trichloroisocyanuric acid, CAS 87-90-1. The TCCA 90 we import is white granular, 5-8 mesh, with 90% minimum available chlorine, and a 1% solution reads pH 2.7-3.3. It is a Class 5.1 oxidiser (UN 2468) and releases toxic chlorine gas on contact with water, acids, ammonia or moisture, so keep it dry and away from other chemicals. It is packed in 25 kg and 50 kg HDPE drums and the manufacturer's batch Certificate of Analysis is supplied.

What is the CAS number and HSN code of bleaching powder?

Bleaching powder is calcium hypochlorite, CAS 7778-54-3, HSN 2828 10 10 (commercial calcium hypochlorite, bleaching powder). We supply the stable grade to IS 1065 (Part 1) with 30-35% available chlorine by mass, in 50 kg HDPE drums. It is a Class 5.1 oxidiser, UN 2208, to be kept cool, dry and away from acids, moisture and organic matter.

How do I choose between bleaching powder, TCCA and hydrogen peroxide?

They are three different oxidisers. Bleaching powder (30-35% available chlorine) and TCCA 90 (90% min available chlorine) are chlorine sources; hydrogen peroxide (35% or 50% w/w) is a clean oxidiser that leaves no chlorinated residue. General guidance, not an SPC specification: the choice depends on the duty (disinfection, oxidation, algae control), the dosing method and how the material can be stored and handled on site. We supply all three; tell us the duty and we will help you match the grade.

What is SMBS, and what is its CAS number?

SMBS is sodium metabisulphite, also written sodium meta bi sulphite, CAS 7681-57-4, formula Na2S2O5. It is a white crystalline powder used as a reducing agent and oxygen scavenger. We supply Industrial Grade (Superior) at 96.0% mass min Na2S2O5 and SO2 content 66.0% mass min, imported, in 25 kg and 50 kg bags with the batch Certificate of Analysis. It releases sulphur dioxide on contact with acids or moisture.

Which chemicals do you supply to control scale in cooling water and ETP systems?

SHMP (Technical Grade, total phosphate as P2O5 68.0% mass min) is listed as a scale and corrosion inhibitor for industrial water treatment. STPP (Technical Grade, 94.0% mass min as Na5P3O10) is listed for scale control in ETP and cooling-water systems. EDTA (di-sodium, technical grade) sequesters metal ions, and sodium gluconate (technical, 98.0-102.0%) is listed for scale and corrosion inhibition in water treatment. We do not publish dose rates.

What is the difference between SHMP and STPP?

Both are sodium phosphates that bind calcium and magnesium hardness, but they are different compounds. SHMP (CAS 10124-56-8) is supplied at total phosphate as P2O5 68.0% mass min, and a 1% solution reads pH 5.8-6.8. STPP (CAS 7758-29-4) is 94.0% mass min as Na5P3O10 with P2O5 57.0% mass min, and a 1% solution reads pH 9.2-10.0. Both are 50 kg HDPE/laminated bags. Which suits a system depends on its pH, temperature and water chemistry.

Which acids and alkalis do you supply for pH correction, and in what packs?

Alkalis: caustic soda flakes (98% min NaOH) in 25 kg and 50 kg bags and 1000 kg jumbo bags, caustic soda lye (IS 252:2013 Grade-1, 47% min NaOH) in bulk road tanker, and soda ash light (99.00% min total alkalinity as Na2CO3) in 50 kg bags. Acids: hydrochloric acid (commercial 30% min, in 35 kg carboys, 200L barrels, 1000L IBCs or rubber-lined bulk tanker), sulphuric acid (commercial 98%, carboys or bulk road tanker) and phosphoric acid (86.0% min H3PO4, 50 kg carboys).

Which products can be supplied in bulk road tanker?

Caustic soda lye (47% min NaOH) is supplied in bulk road tanker, sulphuric acid in carboys or bulk road tanker, and hydrochloric acid in bulk rubber-lined tanker. Other products in this range are packed in bags, drums, carboys, barrels or IBCs as shown in the table. Send your volume and unloading arrangement with the enquiry.

Are your products suitable for drinking water?

Our grades are technical or industrial unless a product page states otherwise, and we do not describe a technical grade as food or pharma grade. Whether a grade is acceptable for potable-water treatment is set by your regulator and plant operator, not by us. Tell us the requirement with your enquiry and we will confirm what the Certificate of Analysis and technical data sheet show.

Do you make antiscalants, coagulants or other finished water treatment products?

No. We supply chemicals for water treatment manufacturers and plant operators: we are an importer and bulk distributor, not a producer of finished antiscalants, dosing blends or coagulants. The range on this page is the raw chemicals themselves. If you need a chemical that is not listed here, send the requirement and we will tell you whether we can source it.

How should oxidisers, acids and sulphites be stored together?

Keep them apart. Oxidisers (bleaching powder, TCCA, hydrogen peroxide) away from acids, reducing agents and combustibles; sulphites (SMBS, sodium bisulphite) away from acids, which release toxic sulphur dioxide; caustic soda dry, tightly closed and away from aluminium, zinc and tin. Never seal hydrogen peroxide containers, because they must vent. Safety data sheets and TDS are available on request.

What documents come with a delivery, and how fast do I get a quote?

A batch Certificate of Analysis is supplied with every delivery, and technical data sheets and safety data sheets are available on request. We quote within 4 working hours of receiving your enquiry. Send the chemical, grade, pack and treatment stage so the quote matches your duty.

Deep guidesHydrogen peroxide in water treatmentEDTA chelating agent guideSodium gluconate buyer guide

Industry Enquiry

Sourcing chemicals for water treatment?

Tell us your requirement — product, quantity, and frequency. We respond within 4 working hours with pricing and availability.